Nina Taylor 
Mounting a Plusinno vertical fishing rod holder takes only a few basic tools and careful wall placement. The PLUSINNO V9 can hold up to 9 rods or combos while using less than 16 inches of wall space. This guide explains how to mark, drill, secure, and test the holder correctly. You will also learn how to avoid common mounting mistakes that can damage rods or walls.
A well mounted rack keeps fishing rods organized, protected, and ready for your next trip. For more details about the Plusinno vertical fishing rod holder, review its design before installation. The V9 uses soft silicone grips that help hold rods securely without unnecessary pressure.
What You Need Before Mounting
First, gather every tool before you start drilling into the wall. You will usually need a pencil, tape measure, level, drill, drill bits, screwdriver, and wall anchors.
Also, keep the supplied screws and mounting hardware nearby during installation. Using the included hardware helps maintain the intended fit and keeps the mounting process simple.
- Plusinno vertical rod holder
- Drill and suitable drill bits
- Screwdriver or drill driver
- Tape measure
- Bubble level
- Pencil or marking tool
- Suitable wall anchors
However, your wall material determines which anchors you should use. A stud provides stronger support than drywall alone, so locate studs whenever possible.
Choose the Right Mounting Location
Start by finding a wall that gives your rods enough vertical clearance. Measure the longest rod and allow additional space for easy removal.
Next, check the area for doors, shelves, vehicles, storage boxes, and other obstacles. A garage wall often works well because it keeps rods off the floor and saves useful storage space.
Keep the holder within comfortable reach when possible. PLUSINNO recommends positioning the rack where anglers can grab rods easily without mounting it excessively high.
Check Wall Construction
Use a stud finder if you have one available. Mark the center of each stud before positioning the rack.
If studs do not align with every mounting hole, use suitable anchors for the remaining holes. Never rely on unsuitable plastic anchors when storing heavy rod and reel combinations.
For concrete or masonry walls, select anchors designed specifically for that surface. Follow the anchor manufacturer’s drill size and installation requirements.
Measure the Rod Holder Position
Hold the rod holder against the wall in your preferred location. Use a level to confirm that the holder sits straight before marking anything.
Then mark every mounting hole with a sharp pencil. Accurate marks prevent crooked installation and reduce unnecessary drilling.
The PLUSINNO V9 uses five mounting holes for secure wall attachment. PLUSINNO also describes the holder as a four step installation design.
Keep the Holder Level
A level holder makes your rod collection look cleaner and function better. It also helps distribute the stored rods more evenly across the rack.
Place the level across the mounting section rather than against a curved edge. Make small adjustments until the bubble stays centered.
How to Mount a Plusinno Vertical Fishing Rod Holder
Step 1: Position the Holder
Place the holder against the wall at your marked location. Confirm that the gripping sections face upward before making the final marks.
This orientation matters because the holder uses upward facing grips to secure the rods. PLUSINNO’s installation guidance specifically recommends pointing these bracket holders upward.
Step 2: Mark the Screw Holes
Use a pencil to mark each mounting hole through the holder. Press the rack firmly against the wall so the marks remain accurate.
After marking, remove the holder and inspect every point. Check that your marks align with studs or suitable wall anchors.
Step 3: Drill Pilot Holes
Choose a drill bit that matches your wall material and anchor requirements. Drill straight into each marked location without forcing the bit.
For stud mounting, drill a suitable pilot hole before driving the screws. For drywall, install the correct anchors before attaching the holder.
PLUSINNO’s own installation guidance recommends drilling pilot holes before installing the anchors and screws.
Step 4: Attach the Holder
Place the rod holder over the prepared holes. Insert each screw and tighten it gradually instead of fully tightening one screw first.
Work across the mounting points to keep pressure balanced. Stop tightening when the holder sits firmly against the wall without damaging the material.
Afterward, check the rack with a level again. Small adjustments remain easier before you load any fishing rods.
Step 5: Test the Mount
Before adding your entire collection, apply gentle pressure to the mounted holder. Check for movement, loose screws, shifting anchors, or wall damage.
If the rack moves, remove the load and inspect the mounting points. Correct the problem before storing valuable fishing equipment.
How to Load Fishing Rods Safely
Once the rack feels secure, begin with one rod or combo. Place the rod into the silicone grip and confirm that it sits naturally.
Then add the remaining rods one at a time. Leave enough room for each rod so you can remove it without disturbing nearby equipment.
The V9 accommodates many rods and combos with diameters from approximately 3 to 19 millimeters. This range covers many common fishing rod sizes, but always check your specific setup.
Arrange Reels Carefully
Stagger reel positions when possible to reduce crowding. The V9 design allows rods and reel combos to sit at different positions along the rack.
This arrangement can improve access when several rods share one holder. It also helps prevent reels from touching each other unnecessarily.
Best Wall Positions for a Fishing Rod Holder
A garage wall provides an excellent location when you have enough vertical clearance. You can keep rods organized while preserving floor space for vehicles and other equipment.
A storage room can also work well when humidity stays controlled. Avoid locations where water regularly splashes onto rods, reels, or mounting hardware.
Basement walls may work for some anglers, but moisture deserves special attention. Excess humidity can affect fishing equipment even when the wall mount remains secure.
Leave Enough Clearance
Measure the rod length before finalizing the rack height. Leave enough room above and below the holder for comfortable loading and removal.
Also, keep rod tips away from ceiling fixtures and nearby shelves. This simple step reduces accidental contact when you remove equipment.
Common Mounting Mistakes to Avoid
Several small installation mistakes can weaken a rod rack. Fortunately, you can prevent most problems with careful preparation.
- Mounting the holder without checking wall construction
- Skipping pilot holes when the wall requires them
- Installing the gripping sections upside down
- Failing to level the holder before tightening screws
- Using unsuitable anchors for heavy equipment
- Overloading the holder beyond its intended capacity
- Placing rods where reels constantly collide
Another common mistake involves mounting the rack too high. A convenient storage system should make your rods easier to access rather than harder.
How to Keep the Holder Secure
Inspect the screws periodically, especially during the first few weeks. Changes in temperature, vibration, or wall movement can sometimes loosen mounting hardware.
Also, check the wall around each anchor for cracks or movement. Fix any structural issue before continuing to store rods on the rack.
The V9 uses a tough polymer body and soft silicone gripping areas. Still, regular inspection helps maintain safe storage over time.
Clean the Gripping Areas
Dust, sand, and grime can collect around fishing equipment. Wipe the gripping areas with a clean, slightly damp cloth when needed.
Remove salt residue after saltwater fishing trips whenever possible. Clean equipment reduces buildup and helps protect both rods and storage surfaces.
Can You Mount It Without Studs?
Yes, you can mount a rod holder on suitable drywall when you use anchors rated for the load. However, stud mounting generally provides a stronger attachment point.
Never assume every drywall anchor can support a loaded rack. Match the anchor type and rating to your wall material and expected equipment load.
If you plan to store heavier combinations, prioritize structural attachment points. The PLUSINNO V6, for example, includes mounting holes designed around standard stud spacing.
How Many Rods Should You Store?
The V9 can store up to nine rods or combos according to PLUSINNO’s product information. However, practical capacity depends on your rod diameters and reel sizes.
Do not force every available position when your equipment feels crowded. Leave enough room to remove individual rods without hitting neighboring reels.
Tips for a Cleaner Fishing Gear Setup
Group rods according to how often you use them. Keep your most frequently used combinations in the easiest positions to reach.
Next, arrange similar rod types together when practical. This system can make preparation faster before fishing trips.
- Place frequently used rods at comfortable heights.
- Keep larger reel combinations separated.
- Store clean rods after each fishing trip.
- Inspect mounting screws regularly.
- Keep rod tips away from obstacles.
Additionally, avoid placing loose hooks near stored rods. Organized tackle reduces the chance of accidental scratches, snags, and equipment damage.
When to Remount the Holder
Remount the holder if you notice repeated movement or damaged anchors. Do not solve a loose mount by simply tightening screws repeatedly.
Inspect the wall material and mounting hardware first. You may need stronger anchors or a different mounting location.
Likewise, move the rack if your current location creates repeated collisions. A better position can protect both your equipment and your storage area.
Final Installation Checklist
Before considering the installation complete, inspect every part of the setup. A quick checklist can catch problems before they affect your fishing equipment.
- Holder sits level against the wall.
- Every mounting point feels secure.
- Anchors match the wall material.
- Gripping sections face upward.
- Rods fit without excessive force.
- Reels have enough clearance.
- Rod tips avoid nearby obstacles.
- The rack stays stable under normal use.
After completing these checks, load your rods gradually. This approach lets you identify problems before placing your full collection on the rack.
Conclusion
Mounting a Plusinno vertical fishing rod holder becomes simple when you measure carefully and secure every mounting point. Start with the right wall location, mark the holes accurately, drill suitable pilot holes, and level the rack before tightening the screws.
Finally, test the holder with one rod before loading the remaining equipment. Follow these steps today to create a cleaner, safer, and easier fishing rod storage system.
Frequently Asked Questions
How many rods can the Plusinno V9 hold?
The Plusinno V9 can hold up to nine rods or rod and reel combos.
Can I mount the Plusinno holder on drywall?
Yes, but you should use anchors specifically rated for your wall material and expected load.
Should the Plusinno holder face upward?
Yes, the gripping sections should face upward so they can secure the rods correctly.
Do I need a drill for installation?
Yes, a drill helps create accurate pilot holes and makes wall installation easier.
What rod sizes fit the V9 holder?
The V9 supports many rods and combos with diameters from about 3 to 19 millimeters.
